1. After the burner is connected to the power supply, press Start and the motor will not rotate.
Solution: If it is locked due to insufficient air pressure, adjust the air pressure to the specified value; if the solenoid valve is not tight and air leaks at the joint, repair or clean the pipe joint of the solenoid valve; if the thermal relay is open, then Press reset to check whether the components are damaged and whether the motor current is damaged; if there is a problem with the water level, pressure, temperature, or program controller power supply, check whether the water level, pressure, and temperature exceed the limits.
2. After the burner is started, the purge is normal, but the ignition does not occur.
Solution: It may be that the gas volume of the electric fire is insufficient, and the circuit needs to be checked and repaired; it may be that the solenoid valve is not working or the solenoid valve is burned out, and it needs to be replaced with a new one; if it is because of unstable air pressure, the air pressure needs to be adjusted to the specified value. ; If it is because the air volume is too large, then it is necessary to reduce the air distribution and reduce the damper opening.
3. The boiler burner does not ignite, the air pressure is normal, and the electricity does not ignite.
Solution: The ignition transformer is damaged, and the ignition transformer needs to be replaced with a new one; the high-voltage wire is damaged or fallen off, and it needs to be reinstalled or replaced; the gap between the ignition rods is too large or too small, and the position needs to be readjusted; the motor is broken Or it is short-circuited to the ground and needs to be reinstalled or updated; there is a problem with the spacing and it needs to be readjusted.
4. The boiler burner turns off after igniting for 5 seconds.
Solution: Insufficient air pressure, too large pressure drop, too small air supply flow, need to readjust the air pressure and clean the filter; too small air volume, insufficient combustion, too thick smoke, or too large air volume, resulting in white smoke. , needs to be readjusted.
5. The boiler burner emits white smoke
Solution: The air volume is too small, turn down the damper; the air humidity is too high, appropriately reduce the air volume and increase the humidity of the inlet air; the exhaust smoke temperature is too low, increase the exhaust smoke temperature.
1. After the burner is connected to the power supply, press Start and the motor will not rotate.
Solution: If it is locked due to insufficient air pressure, adjust the air pressure to the specified value; if the solenoid valve is not tight and air leaks at the joint, repair or clean the pipe joint of the solenoid valve; if the thermal relay is open, then Press reset to check whether the components are damaged and whether the motor current is damaged; if there is a problem with the water level, pressure, temperature, or program controller power supply, check whether the water level, pressure, and temperature exceed the limits.
2. After the burner is started, the purge is normal, but the ignition does not occur.
Solution: It may be that the gas volume of the electric fire is insufficient, and the circuit needs to be checked and repaired; it may be that the solenoid valve is not working or the solenoid valve is burned out, and it needs to be replaced with a new one; if it is because of unstable air pressure, the air pressure needs to be adjusted to the specified value. ; If it is because the air volume is too large, then it is necessary to reduce the air distribution and reduce the damper opening.
3. The boiler burner does not ignite, the air pressure is normal, and the electricity does not ignite.
Solution: The ignition transformer is damaged, and the ignition transformer needs to be replaced with a new one; the high-voltage wire is damaged or fallen off, and it needs to be reinstalled or replaced; the gap between the ignition rods is too large or too small, and the position needs to be readjusted; the motor is broken Or it is short-circuited to the ground and needs to be reinstalled or updated; there is a problem with the spacing and it needs to be readjusted.
4. The boiler burner turns off after igniting for 5 seconds.
Solution: Insufficient air pressure, too large pressure drop, too small air supply flow, need to readjust the air pressure and clean the filter; too small air volume, insufficient combustion, too thick smoke, or too large air volume, resulting in white smoke. , needs to be readjusted.
5. The boiler burner emits white smoke
Solution: The air volume is too small, turn down the damper; the air humidity is too high, appropriately reduce the air volume and increase the humidity of the inlet air; the exhaust smoke temperature is too low, increase the exhaust smoke temperature.